+1 888 963 9028

Raise3D Academy

How to Set Up Raise3D PVA to Print

How to Set Up Raise3D PVA to Print

Part of using a 3D printer from Raise3D is knowing how to properly set up and prepare filaments for printing. One example PVA is a water-soluble 3D printing filament. Learn how to print with PVA on a Raise3D printer while also following the generic steps of printing with a filament.

 

Required Tools:
-PolyBox (Dry box)
-Desiccants
-Guide Tube

 

Polybox

 

Preparation

1. Adjust nozzle heights and X/Y offsets to make sure the printer is properly printing dual color extrusion before attempting to use Raise3D PVA.

Note: For more information, please read our tutorial on the website “Manual Pro2 Series – How to Calibrate the Nozzle Offset -V1.0, Manual Pro2 Series – How to Calibrate the Nozzle Height – V1.0”.

 

2. Put the PVA filament in the Polybox and thread one end out of the box through the guide tube.

 

3. Remove the lid from your Raise3D printer.

Note: Room temperature should be about 18℃ or 65℉ degrees, if the room temperature is colder please use the lid on your Raise3D Printer.
PVA material is sensitive to moisture, and the Polybox is used for moisture control. Raise3D PVA does not need to be dried when first removed from the vacuum-sealed bag. However, if the PVA spool is left out after printing, it will need to be dried with a Print-dry system. Load a spool of Raise3D PVA into the Polybox and wait until the humidity is under 15%.

 

Raise3D PVA into the Polybox and wait until the humidity is under 15%.

 

4. Insert each guide tube into the Filament Run-out Sensor and load the PVA and PLA filaments into both hotend. Load the Raise3D PVA filament into the right hotend and load another filament into the left hotend.

Note: In the event of a failed print job, check if the Raise3D PVA filament is fully dried, or you may change the desiccant in the Polybox and dry the Raise3D PVA filament again.

 

Load the PVA and PLA filaments into both hotend

 

5. The tube must be smooth and without knots or bends. The Polybox should be placed higher than the printer. Do not load PVA into the left hotend.

 

Polybox and hotend

Setting ideaMaker to use Raise3D PVA

Note: Make sure to use the latest version of the ideaMaker.

6. Open ideaMaker

 

Open ideaMaker

 

7. Click “File” located at the top left side. Select “Import Models” from the drop-down menu.

 

Select “Import Models” from the drop-down menu

 

8. Click the “Start Slicing” button at the top center

 

Click the “Start Slicing” button at the top center

 

9. Make sure to select “[Raise3D] PVA 1.75mm” filament for the right extruder to prevent printing issues with the Raise3D PVA from happening

 

select “[Raise3D] PVA 1.75mm” filament for the right extruder

 

10. Select a Template.

Note: We use “High Quality – Pro2 – PLA” as an example below

Select a Template

 

11. Click the “gear” button on the right side of “[Raise3D] PVA 1.75mm” to check the Raise3D PVA Filament Settings.

 

Click the “gear” button on the right side of “[Raise3D] PVA 1.75mm

 

It checks the Raise3D PVA Filament Settings

12. The option of “Override Slicing Settings in Templates Linked to the Filament” is a default setting for Raise3D PVA.

 

Override Slicing Settings in Templates Linked to the Filament is a default setting for Raise3D PVA

 

13. Close the « Filament Settings » and click the « Edit » button followed by the « Advanced » button.

Note: Advanced menu may pop up right after clicking “Edit” if you have already entered in advanced mode.

 

Close-the-Filament-Settings-and-click-the-Edit-button-followed-by-the-Advanced-button

 

 

Advanced menu may pop up right after clicking “Edit”

 

14. Under the « Advanced » setting, select the “Support” tab and click the “General Support”. A drop-down menu will appear. Choose the option “All”.

 

Under the "Advanced" setting, select the “Support” tab and click the “General Support”

 

15. Locate the « Support Extruder » option on the left column under the « Support » tab. Select “Right extruder” from the drop-down menu. Then locate the « Dense Support Extruder » on the right column, and select “Right Extruder” from the drop-down menu.

 

Locate-the-Support-Extruder-option-on-the-left-column-under-the-Support-tab

 

16. Click the “Temperature” tab and tick the “Cool Down Inactive Extruder »

Click the “Temperature” tab and tick the “Cool Down Inactive Extruder”

 

17. Click “Save” to save these changes

Click “Save” to save these changes

 

18. Click “Slice” to start slicing the model

Click “Slice” to start slicing the model

Print

19. Apply PVA glue stick to the print build surface.

 

20. Check the adhesion of first layer printing to verify that the edges have not warped.

Preview:

 

Check the adhesion of first layer printing to verify that the edges have not warped

 

Check the adhesion of first layer printing to verify that the edges have not warped second preview

 

21. While printing it is a good idea to make sure the PLA and PVA are at the same height to ensure supported surfaces come out as cleanly as possible.

Note: If the material heights are not equal or you notice poor surface finish on supported surfaces, your nozzle offsets may need to be recalibrated.

 

Make sure the PLA and PVA are at the same height

 

Nozzle offsets may need to be recalibrated if height is not equal

 

22. Finished product

 

Finished product

 

 

 

PVA Printing Video

For more information about 3D printers and 3D printing, visit and subscribe to the official Raise3D Youtube channel

Connect with Raise3D:

Have you had a great experience with Raise3D that you would like to share? Please contact us at inquiry@raise3d.com. We look forward to hearing from you.

For more information about Raise3D printers and services, browse our website, or schedule a demo with one of our 3D printing experts.